Technical & Electrical Specifications

Max Current Rating

1000 A

Terminal Pinouts & Hardware Connections

Verify physical terminal sizes, stud threads (M6, M8, M10), and circuit polarity before crimping lugs or running wiring.

Hardware terminal connection details and stud sizes for Lynx Distributor (1000A)
Terminal Label	Polarity / Type	Nominal Voltage	Physical Hardware	Location
POS IN main_pos_in	+ DC Positive	12.0V	Standard Terminal	Left Panel
NEG IN main_neg_in	- DC Negative	12.0V	Standard Terminal	Left Panel
POS OUT main_pos_out	+ DC Positive	12.0V	Standard Terminal	Right Panel
NEG OUT main_neg_out	- DC Negative	12.0V	Standard Terminal	Right Panel
F1+ fuse1_pos	+ DC Positive	12.0V	Standard Terminal	Bottom Panel
F1- fuse1_neg	- DC Negative	12.0V	Standard Terminal	Bottom Panel
F2+ fuse2_pos	+ DC Positive	12.0V	Standard Terminal	Bottom Panel
F2- fuse2_neg	- DC Negative	12.0V	Standard Terminal	Bottom Panel
F3+ fuse3_pos	+ DC Positive	12.0V	Standard Terminal	Bottom Panel
F3- fuse3_neg	- DC Negative	12.0V	Standard Terminal	Bottom Panel
F4+ fuse4_pos	+ DC Positive	12.0V	Standard Terminal	Bottom Panel
F4- fuse4_neg	- DC Negative	12.0V	Standard Terminal	Bottom Panel
GND chassis_gnd	⏚ Chassis Ground	12.0V	Standard Terminal	Top Panel

Installation Safety Standard: Always size circuit protection (ANL, MIDI, or MEGA fuses) to protect the cable run attached to these terminals against dead shorts and thermal overload, in compliance with AS/NZS 3001, AS/NZS 3004, and ABYC E-11 standards.

Official Product Manual & Wiring Guidelines

Manufacturer technical instructions, safety precautions, and troubleshooting procedures.

1. Safety Instructions

WARNING: LIVE BUSBARS SHOCK HAZARD
Do not work on live busbars. Ensure that the busbar is unpowered by disconnecting all positive battery poles prior to removing the Lynx front cover.

QUALIFIED PERSONNEL ONLY
Work on batteries and DC systems should be carried out by qualified personnel only. Observe the battery safety warnings as listed in the battery manual.

Transport and Storage

Store this product in a dry environment.
The storage temperature should be: -40°C to +65°C.
No liability can be accepted for damage in transit if the equipment is not transported in its original packaging.

Power & Electrical Ratings
Voltage Range	9 - 60Vdc
Supported System Voltages	12V, 24V or 48V
Reverse Polarity Protection	Yes (RJ10 port is NOT protected)
Current Rating	1000Adc continuous
Power Consumption	Max 100mA (with all LEDs illuminated)

Connections
Busbar Joints	M8 or M10 (version-dependent)
Fuses	M8 studs (MEGA fuses)
Power & Data Connection	40 cm RJ10 cable (included)

Physical & Environmental
Enclosure Material / Dimensions	ABS / 290 x 170 x 80 mm
Unit Weight	2.2 kg
Busbar Material / Size	Tinned copper / 8 x 30 mm
Operating & Storage Temp	-40°C to +60°C / -40°C to +65°C
Humidity & Protection	Max. 95% (non-condensing) / IP22

Symptom	Possible Cause	Remedy
No LEDs illuminated	No power supplied over RJ10 cable.	Check RJ10 connection on both sides. Ensure Lynx Shunt or Smart BMS is powered.
Fuse status not showing on GX device	RJ10 connection issue or not connected to Lynx Smart BMS.	Ensure unit is connected to a Lynx Smart BMS (not Lynx Shunt). Check for RJ10 cable damage.
Terminals running hot	Loose contact / dirty terminal surfaces.	Disconnect DC power, clean copper busbar joints, and re-torque nuts.

Lynx Distributor (1000A)

Technical & Electrical Specifications

Terminal Pinouts & Hardware Connections

Official Product Manual & Wiring Guidelines

1. Safety Instructions

Transport and Storage

2. Description

The Lynx Distributor

The RJ10 Cable

MEGA Fuses

3. Technical Specifications

4. Installation & Connections

4.1 Interconnecting Lynx Modules

4.2 Mechanical Mounting

4.3 Electrical Connections

5. Troubleshooting & Support

LED Indications

Common Operational Issues

Plan Your System with the Lynx Distributor (1000A)

Component Summary

Related 12V Calculators

Matching Equipment